Alecto DVM-275 manual

Alecto DVM-275
7.5 · 1
PDF user manual
 · 2 pages
user manualAlecto DVM-275


Power supply:
The baby unit (camera) is powered by the
included 5V power adaptor with the straight
(micro USB) plug.
Make sure that the baby can’t touch the wire of the baby unit
or the adaptor cord. Place the
baby unit at least 1-1.5 meters
away from the baby and bundle
excess cable lengths using tape or
this purpose.
The parent unit (monitor) is powered by the
permanently installed and non-exchangeable
battery. This battery is recharged by connect-
ing the supplied 5V power adaptor with the
perpendicular (micro USB) plug to the rear of
the parent unit.
Insert the power adaptors into a 230V wall outlet.
Only use the supplied power adaptors with the
The specications of both adaptors are identical. That’s
why it won’t cause any problems when accidentally
interchanging the adaptors.


Signal strength:
strong reception
good reception
average reception
poor reception
no reception
sound is enabled
Attention, this doesn’t indicate the set volume
sound is disabled (volume set to 0)
Attention, when disabling the sound while the VOX
function is active (for this, see ‘menu operated
functions’), the speaker symbol will keep indicating that
the sound is enabled
Feeding timer:
in the lower right corner of the screen
Temperature alert:
the temperature alert is enabled
(‘22’ is an example)
Indicates the temperature in the room where the baby unit
is situated; take into account a possible tolerance of ± 1.5
23:07:25 (‘23:07:25’ is an example)
The time is displayed in the upper right corner of the screen.
battery full
alert tones will sound for approximately 20 to 30 minutes.
Zoom function:
Switching on/o󰀨:
 button at the front of the baby unit to
switch on the baby unit. The indicator directly underneath the
 button again to
power adaptor.
then completely to the right and then fully down and up. Final-
The arrow buttons on the parent unit allow you to aim the
camera at the desired spot.
Automatic night vision:
dark and will switch of again when it becomes light.
The LEDs can illuminate objects up to a distance of
approximately 3-5 meters.
When it’s dark, that is when the night vision LEDs are
switched on, the images on the parent unit will be
displayed in black and white.
Attention: infra-red light cannot be perceived by the
human eye; that means you cannot tell whether the
infra-red LEDs are switched on with the naked eye.
Switching on/o󰀨:
Press and hold button for 3 seconds to switch the parent
  
symbol appears when the
sound is disabled.
Sound indicators:
whether the baby is crying. In this way you can also monitor
baby monitor is located a bit further away in the room.
To talk back:
Press the button to talk back to your baby. Keep the button
depressed for as long as you’re speaking and release the
button to listen.
While using the talk-back function, the icon appears
in the screen.
Display o󰀨 (parent sleep mode):
If the display brightness of the parent unit on your bedside
by pressing the button. The sound remains enabled.
See the section ‘VOX’ to automatically switch o the
screen + sound when the baby is sleeping and to
switch them on again as soon as the baby starts crying
Press and hold the   or button to aim the camera to
The sound is disabled while orienting the camera of the
baby unit.
ZOOM: (enlarging)
 
button again to restore the normal view.
screen when this function is enabled.


 button.
Use the navigation button   or to select the desired
option. Press the OK button to open the selected option.
    or to select the
‘Lullabies’ option and press the OK button
   or button to select the desired lullaby or
3. Press 2x the button to leave the menu and to return to
the normal screen or wait for 10 seconds until this happens
Playback of the lullabies is stopped automatically after
approximately 20 minutes. You may also open the
menu and select STOP to stop playing the songs earlier.
At the bottom of the menu you also have the option to
adjust the playback volume of the lullabies at the baby
Keep in mind that the sound of the lullaby is returned to
the parent unit via the microphone of the baby unit. In
this case, you may want to set the sound of the parent unit to
level 0 (= sound o).
As soon as and for as long the lullabies are being
played, the symbol appears at the top in the display.
you may use this menu to select which view must be dis-
played in the screen.
    or to select the
‘View’ option and press the OK button
 or button to select which camera you’d like to
5 seconds one after the other and press the OK button
Attention: The unit does NOT automatically switch to a
camera where sounds are being detected.
This menu allows you to input a minimum and maximum value
    or to select the
‘Temperature’ option and press the OK button
  
‘Low Temperature’ for the minimum temperature
set these options with the or button
‘OFF’ to disable the temperature alert
press the OK button to select this setting
3. Press 2x the button to leave the menu and to return to
the normal screen or wait for 10 seconds until this happens




have the baby monitor switch on.
foil from the parent and baby unit.
About this users manual:
always adhere to the instructions described in this
This symbol is followed by a user’s tip.
this user’s manual.
Press and hold for 3 seconds to switch the parent unit on
again to switch the display back on.
press  and repeatedly to increase or decrease the
press and hold to move the camera up or down (tilt
press  and repeatedly to select the desired setting
press and hold to move the camera left or right (pan
press  and repeatedly to select the desired setting
register the baby unit on the
parent unit. See the related
instructions further on in this
Parent unit table stand:
the stand at the rear of the device.
Baby unit wall mount:
” tripod nail
bracket to place the baby unit in a higher position or to mount


press again to restore the normal view.
selected setting.
2 5

View the manual for the Alecto DVM-275 here, for free. This manual comes under the category baby monitors and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the Alecto DVM-275 or do you need help? Ask your question here

Need help?

Do you have a question about the Alecto and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Alecto owners to provide you with a good answer.

Number of questions: 0

Sit back and enjoy crystal-clear visuals and images with the vibrant quality of 2 million pixels. The 1920 x 1080 resolu...
DVM-275 | DVM-275
baby monitor
User manual (PDF)
Weight & dimensions
Transmitter height130 mm
Transmitter width75 mm
Transmitter depth75 mm
Receiver height95 mm
Receiver width163 mm
Receiver depth15 mm
Product colourWhite
Housing materialPlastic
AC input voltage110-240 V
AC input frequency50-60 Hz
Power source typeAC, Battery
Display typeLCD
Display diagonal5 "
Display resolution480 x 272 pixels
Maximum indoor range50 m
Maximum outdoor range300 m
Temperature sensor
Built-in microphone-
Built-in speaker(s)-
Maximum range- m
Smartphone support-
Packaging data
Package weight690 g
Ports & interfaces
Night mode
Packaging content
AC adapter included
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Alecto DVM-275 below.

Is your question not listed? Ask your question here

No results