Barracuda Networks SSL VPN 480 manual

Barracuda Networks SSL VPN 480
7.6 · 1
PDF user manual
 · 2 pages
user manualBarracuda Networks SSL VPN 480


Barracuda SSL VPN - Quick Start Guide

The Barracuda SSL VPN is a secure remote access appliance that allows you to access
your internal network resources such as files, intranet Web sites and client/server
applications using just a standard Web browser. It is common for the Barracuda SSL
VPN to be installed directly inside your LAN or in a more advanced DMZ configuration.
Getting Started
This guide provides you with setup instructions for the Barracuda SSL VPN. We
recommend reading these instructions fully before starting the setup. To begin
setting up your Barracuda SSL VPN, you will need the following:
Barracuda SSL VPN
AC Power Cord
Ethernet Cables
VGA Monitor (recommended)
PS2 Keyboard (recommended)
Physical Installation
To install the Barracuda SSL VPN:
1. Fasten the Barracuda SSL VPN to a 19-inch rack or place it in a stable
2. Connect an Ethernet Cable from your network switch to the Ethernet port on
the back of the Barracuda SSL VPN.
3. Connect a Standard VGA Monitor, PS2 Keyboard, and AC power cord to the
Barracuda SSL VPN. Note: Immediately after connecting an AC Power Cord
to the Barracuda SSL VPN, it may power ON for a few seconds and then
power OFF. This is because the Barracuda SSL VPN is designed to
automatically return to a powered ON state in the event of a power outage.
4. Press the POWER button on the front panel to turn it on.
Configure IP Address and Network Settings
If you have a monitor connected, the Barracuda SSL VPN will display the Boot
Menu initially, and the Administrative Console login prompt once fully booted.
To begin the configuration:
1. Login to the Administrative Console using the admin login:
Login: admin
Password: admin
2. Configure the IP Address, Subnet Mask, Default Gateway, Primary DNS
Server and Secondary DNS Server as appropriate for your network.
3. Save your changes.
If you do not have a monitor and keyboard and want to set the IP address using
the RESET button on the front panel, press and hold the RESET button per the
following table:
IP address Press and hold RESET for 5 seconds 8 seconds 12 seconds
Opening Firewall Ports
If your Barracuda SSL VPN is located behind a corporate firewall, ensure that
the following ports on your firewall are open to ensure proper operation.
Port Direction TCP UDP Usage
25 Out Yes No Email alerts + One-time passwords
53 Out Yes Yes Domain Name Service (DNS)
80 Out Yes No Virus, firmware and updates
123 Out No Yes Network Time Protocol (NTP)
443 In/Out Yes No HTTPS/SSL port for SSL VPN access
8000 In/Out Yes No Appliance administrator interface port (HTTP)
8443 In/Out Yes No Appliance Administrator interface port (HTTPS)
Note: The Appliance Administrator interface ports on 8000/8443 should only be
opened if you intend to manage the appliance from the Internet.
Barracuda SSL VPN Configuration
Use a computer with a Web browser that is connected to the same network as
the Barracuda SSL VPN and follow these steps:
1. In your Web browser’s address bar, enter http:// followed by the IP address
of the Barracuda SSL VPN, followed by the default Appliance Administrator
Web interface HTTP port (:8000). For example, if you configured the
Barracuda SSL VPN with an IP address of, you would type:
2. Log in to the Appliance Administrator Web interface as the administrator:
Username: admin
Password: admin
3. Go to the Basic
IP Configuration page and perform the following:
Verify the IP Address, Subnet Mask, and Default Gateway.
Verify the Primary and Secondary DNS Server.
If you are using a proxy server on your network, you should also verify the
Proxy Server Configuration settings.
4. Click any one of the Save Changes buttons to save all of the information.

View the manual for the Barracuda Networks SSL VPN 480 here, for free. This manual comes under the category not categorized and has been rated by 1 people with an average of a 7.6. This manual is available in the following languages: English. Do you have a question about the Barracuda Networks SSL VPN 480 or do you need help? Ask your question here

Need help?

Do you have a question about the Barracuda Networks and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Barracuda Networks owners to provide you with a good answer.

Number of questions: 0

Barracuda Networks
SSL VPN 480 | BVSI480A3
not categorized
Manual (PDF)
Weight & dimensions
Dimensions (WxDxH)427 x 356 x 43 mm
Weight5400 g
Number of users100 user(s)
Authentication method802.1x RADIUS
Ethernet LAN interface typeFast Ethernet
Cabling technology10/100Base-T(X)
Ports & interfaces
I/O ports1 x RJ45, \n1 x VGA, \n1 x PS/2, \n1 x DB9
AC input voltage100-240 V
AC input frequency50 - 60 Hz
Power source typeAC
show more

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Barracuda Networks SSL VPN 480 below.

What is the weight of the Barracuda Networks SSL VPN 480?

The Barracuda Networks SSL VPN 480 has a weight of 5400 g.

Is the manual of the Barracuda Networks SSL VPN 480 available in English?

Yes, the manual of the Barracuda Networks SSL VPN 480 is available in English .

Is your question not listed? Ask your question here

No results