Name: EnerGenie Mi Home Double Light Switch
Brand: EnerGenie
SKU: 1297182
Rating: 75 (1 reviews)

user manualEnerGenie Mi Home Double Light Switch

Mi Home Double Light Switch

Quick Start Guide

The Double Light Switch is part of the MiHome home

automation range for the switching of mains power to lighting

up to 250W (50W for LEDs) per circuit. The product can be

controlled manually via the push button. Used with a MiHome

Gateway (MIHO001) registered to a MiHome account, it can

also be controlled remotely via the MiHome smartphone app

or through a browser.

In the Box:

Double light switch, Screw ﬁttings, User guide

Compatibility

We recommend incandescent & halogen bulbs which are

250W max, or dimmable LED bulbs which are maximum 50W

in total andnot exceeding 6 bulbs per circuit.Not suitable for

ﬂuorescent, non-dimmable LED and CFL bulbs or any light

requiring line drivers.

Installation

This device operates at UK mains voltage levels therefore we

advise installation from a competent, qualiﬁed person.It can

ﬁt into a 25mm metal back-box or 35mm dry lining back-box,

but not into a 4 lug box. Please see "Installation Example"

section for wiring information.

Installation Notes

• Can only be used in a two-way switching conﬁguration with

a MiHome slave switch on circuit 1 (circuit 1 on MIHO009

labelled L, S1, L1).

• Using any other switch as a slave will damage the Light

Switch.

• The product requires power to circuit 1. If the power to both

circuits is removed while circuit 2 is switched on, and then

restored only to circuit 2, circuit 2 lamps will be lit whilst the

LED will be o. When power is restored to circuit 1 as well,

control for circuit 2 will also be restored, and the circuit 2

lamps will turn o.

Important

Applicable in England and Wales, where the installation of

this product falls under the scope of the Building Regulations

requirements for Part P, the installation must be carried out by

registered competent persons, and work should be designed

and installed, and inspected, tested and certiﬁcated in

accordance with BS 7671.

Applicable in Scotland, where the installation of this product

falls under the Building (Scotland) Act, a Warrant may be

required and advice should be sought from LABSS (Local

Authority Building Standards Scotland). We recommend that

a competent qualiﬁed person is used for all installations of

thisproduct.

Pairing with the MiHome Gateway

In order to control your Double Light Switch from the mobile

app or from a browser, it needs to ﬁrst be paired with the

MiHomeGateway, as follows:

Pairing via the App on your Smartphone:

The Appmaybe downloaded free of charge from the Google

Play or iOS App Store.

1. Log into your MiHome account on the MiHome App.

2. Ensure there is power to the Double Light Switch, and the

Double Light Switch is switched o.

3. Select "Add a new device" from menu and then choose "

Double Light Switch ", then choose Left or Right side as

required.

4. Follow onscreen pairing instructions,pressing the Double

Light Switch button when required for at least 8 seconds until

the LED begins to ﬂash, and then release.

5. The LED will ﬂash rapidly for a few seconds to indicate that

the Double Light Switch is being paired, the LED will go o

when this is complete.

6. The Double Light Switch should now be visible in the

device list (may take a few seconds depending on network

speed),refresh your browser if necessary.

7. Repeat steps 1-6 for the other switch side (left or right) as

required, always allow 1 minute between pairing devices or

dierent sides of the same device.

Pairing via a Browser

1. Log into your account atmihome4u.co.uk.

2. Ensure there is power to the Double Light Switch, and the

Double Light Switch is switched o.

3. Select "Pair New Device", then click on the " Double Light

Switch " icon from the available options. Next click the "Pair

Device" button.

4. Follow onscreen pairing instructions,pressing the Double

Light Switch button when required forat least 8 seconds until

the LED begins to ﬂash, and then release.

5. The LED will ﬂash rapidly for a few seconds to indicate that

the Double Light Switch is being paired, the LED will go o

when this is complete.

6. The Double Light Switch should now be visible in the

device list (may take a few seconds depending on network

speed),refresh your browser if necessary.

7. Repeat steps 1-6 for the other switch side (left or right) as

required, always allow 1 minute between pairing devices or

dierentsides of the same device.

Operation Notes

1. A single press of the button while it is ﬂashing will take it

out of pairing mode.

2. The Double Light Switch can be paired with up to 3

separate gateways. Further attempts to pair will overwrite

previous pairings.

Reset

The reset procedure will clear the memory of all paired

devices for the selected circuit (left or right).

1. Ensure there is power to the Double Light Switch, and the

Double Light Switch is switched o.

2. To reset the Double Light Switch, press and hold the left or

right button as required for approximately 30 seconds, until

the LED has returned to steady ON. During these 30

seconds, the LED sequence will be, ON > Slow Flash > ON >

Quick Flash > ON.

Manual operation

A single short press of the button on the front of the housing

will toggle the Light Switch on or o. In normal use, the

buttons should not be pressed more than once every 3

seconds.

Disposal

The inner and outer cardboard packaging is 100% recyclable.

Do not dispose of the Double Light Switch with regular

household waste. You must take electronic equipment to a

local recycling centre to be disposed of in line with current

regulations. For local recycling information see

www.gov.uk/recycling-collections

and for MiHome and Energenie recycling information see

www.energenie4u.co.uk/support/weee_and_weeeco_information

Safety

You must only use the product in dry areas indoors, and it must

be protected from moisture and water.Do not disassemble, as

it does not contain any parts to service.This device and

associated software are for use solely in domestic, commercial

and light industrial environments, and should not be used in

applications which require safety critical, or high risk

applications. For more information please see the full user

manual for this product.

Technical Speciﬁcation

• Rating: 220 - 240V~ 50Hz, 1A, 250W max (50W for LEDs)

per circuit

• Switching: Line only

• Terminal Connections: Circuit 1 - L (Line in), L1 (Line out), S1

(MiHome only); Circuit 2 - Lx (Line in), L2 (Line out).

• Radio: 433.92MHz ISM short range receive only

• Range: Approx. 15-20m in closed; 30m in open area

• Operating temp. : -5°C to 40°C

• Storage temp. : -20°C to +60°C

• Mounting: 25mm metal pattress; 35mm dry lining

• Size (HxWxD): 85 mm x 85 mm x 28mm; Weight: 105g

• Protection class: IP20

Further Help

If you have any questions regarding your product or you believe

it to be faulty, please visit mihome4u.co.uk/troubleshooting

and/orenergenie4u.co.ukwhere you can download a more

comprehensive user manual, or contact us directly on tel:

08000 469 466or e-mail:support@mihome4u.co.uk

Simpliﬁed EU Declaration of Conformity

Hereby, Sandal Plc, T/a Energenie declares that the radio

equipment typeMIHO009 Double Light Switch(including

variations of ﬁnish with metal and plastic fascias) arein

compliance with the following Directives: 2014/53/EU Radio

Equipment Directive (Article 3.1 a & b, and 3.2), 2012/19/EU

Waste Electrical and Electronic Equipment (WEEE) Directive &

2011/65/EU Restriction of the Use of Certain Hazardous

Substances (RoHS) Directive Recast.

The full text of the EU declaration of conformity is available

within the full user manual which can be downloaded at the

following internet address:www.energenie4u.co.uk

The Technical Construction File required is maintained at the

company headquarters at 5 Harold Close, The Pinnacles,

Harlow, Essex, England, CM19 5TH.

Warranty

If you do not install the productand use it in line with this

guide the warranty will become invalidated and we will not be

liable for any damage or loss whatsoever, including indirect

loss, damage to property or personal injury.Your statutory

rights are not aected.

View the manual for the EnerGenie Mi Home Double Light Switch here, for free. This manual comes under the category smart home and has been rated by 1 people with an average of a 7.5. This manual is available in the following languages: English. Do you have a question about the EnerGenie Mi Home Double Light Switch or do you need help? Ask your question here

Need help?

Do you have a question about the EnerGenie and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other EnerGenie owners to provide you with a good answer.

Number of questions: 0

EnerGenie Mi Home Double Light Switch #1

General

	EnerGenie
	Mi Home Double Light Switch \| MIHO092
	smart home
	English
	Manual (PDF)

Features

Connectivity technology	Wireless
Wireless technology	-
Product colour	Silver, White
Operating frequency	433.92 MHz
Maximum outdoor range	30 m

Power

Power source	AC
AC input voltage	220-240 V
AC input frequency	50 Hz
Input current	1 A
Connected load	250 W

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the EnerGenie Mi Home Double Light Switch below.

Is your question not listed? Ask your question here

No results