all relevant laws in your jurisdiction before using
this product for surveillance purposes to ensure
that your use of this product conforms.
Please refer to the product specication for
camera parameters and functions.
Introduction
Please read these instructions carefully and keep them
for future reference. You must heed all the warnings
and cautions as well as follow all the safety and instal-
lation instructions.
Safety Instructions
Make sure that you only use the power adapter that is
specied in the specications sheet of the product. If
you use any other adapter or connect the power supply
incorrectly, this may cause explosion, re, electric
shocks or damage the product.
User Manual
1 INTRODUCTION
This series of camera adopts new generationsensor with high sensitivity and advanced circuitdesign technology. It features high resolution,low image distortion and low noise, etc. , whichmakes it suitable for surveillance system andimage processing system.• High performance CMOS sensor and high resolution bring high-quality image;• Low illumination;• OSD menu, parameters are congurable;• Support auto white balance, auto gain control,• Support image effect adjustment;• Unit transmission control;• Advanced 3 - axis design meets differentinstallation requirements.1.2 Overview1.2.1 Overview of Type I Camera
Figure 1-1 Overview of Type I Camera
1.2.2 Overview of Type II Camera
Figure 1-2 Overview of Type II Camera
1.2.3 Overview of Type III Camera
Figure 1-3 Overview of Type III Camera
Abetechs GmbH 20171127 www.Grundig-Security.com
GD-CT-AC2116T
TVI Bullet Camera
User Guide
GRUNDIG-SECURITY.COM
2 INSTALLATION
Before you start:
• Please make sure that the device in the package is in good condition and all the assembly parts are included.• Make sure that all the related equipment is pow-er-off during the installation.• Check the specication of the products for the installation environment.• Check whether the power supply is matched with your power output to avoid damage.• Please make sure the wall is strong enough towithstand three times the weight of the camera and the mounting.• If the wall is made of cement, you need to insert expansion screws before you install the camera.If it is a wooden wall, you can use self-tapping screw to secure the camera.• If the product does not function properly, please contact your dealer or the nearestservice center. Do not disassemble the camera for repair or maintenance by yourself.2.1 Installation of Type I Camera
Steps:
1. Drill the screw holes according to the drilltemplate.2. Screw the clip plate onto the mounting baseloosely.
Figure 2-1 Drill Template
3. Route the cables to the cable hole and connectthe corresponding power cable and video cable.4. Fix the camera to the ceiling with the suppliedscrews.
Figure 2-2 Fix the Camera to the Ceiling
Do not connect several devices to one power adapter
as this may cause an adapter overload and can lead to
over-heating and re. Make sure that the plug of the
power adapter is rmly connected to the power socket.
Do not use any accessories that are not recommended
by GRUNDIG. Do not modify the product in any way.
If the product starts to smell or smoke comes out of
the device, immediately stop using the product and
disconnect it from the power supply to prevent re
or electric shocks. Then contact your dealer or the
nearest service center.
If the product does not work correctly, contact your
dealer or nearest service center. Never open, disas-
semble or alter the product yourself. GRUNDIG cannot
accept any liability or responsibility for problems
caused by attempted and unauthorized repair and
maintenance.
Do not aim the camera or camera lens at a strong light
such as the sun or a bright lamp. Irreversible damage
to the camera can be caused by a strong light.
Do not expose the sensor of the product to laser beams
as this may damage the sensor.
Do not install the product near radiation sources.
Do not install the product near heat sources, like radi-
ators or other equipment that produces some heat.
Installation References
Do not install the product on surfaces or in places that
are vibrating. This product is not dedicated to be used
in vehicles, trains etc..
Do not touch the sensor module with your ngers.
Always adjust the focus by using a grey lter or at low
illumination.
If the product supports IR, you need to take some
precautions to prevent IR reection. Do not install the
product close to reective surfaces of objects as this
may cause reection. The foam ring around the lens
must be seated ush against the inner surface of the
bubble to isolate the lens from the IR LEDS.
View the manual for the Grundig GD-CT-BC2116T here, for free. This manual comes under the category Security cameras and has been rated by 1 people with an average of a 9.9. This manual is available in the following languages: English. Do you have a question about the Grundig GD-CT-BC2116T or do you need help? Ask your question here
Need help?
Do you have a question about the Grundig and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Grundig owners to provide you with a good answer.
Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Grundig GD-CT-BC2116T below.
What is a megapixel?
The number of megapixels denotes how many pixels there are in the sensor. 1 megapixel equals 1 million pixels. The more pixels, the higher the potential image quality.
What does the abbreviation 'MP' stand for?
MP stands for MegaPixels.
Is the manual of the Grundig GD-CT-BC2116T available in English?
Unfortunately, we do not have the manual for the Grundig GD-CT-BC2116T available in English. This manual is available in English.
Need help?
Do you have a question about the Grundig and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Grundig owners to provide you with a good answer.
Number of questions: 0