Panasonic CQ-RX102N manual

Panasonic CQ-RX102N
7.2 · 2
PDF user manual
 · 24 pages
user manualPanasonic CQ-RX102N

Upute za uporabu

AAC WMA MP3 CD reproduktor/prijamnik
Model: CQ-RX400N/CQ-RX300N
WMA MP3 CD reproduktor/prijamnik
Model: CQ-RX200N/CQ-RX103N/


Prije uporabe ovog ureðaja pažljivo proèitajte ove upute i saèuvajte ih za kasniju uporabu.
Montažni okvir
Prednji okvir
Naponski prikljuèak
\CQ-RX400N\ \CQ-RX300N\
Daljinski upravljaè (ukljuè
uje i
\CQ-RX400N\ \CQ-RX300N\
Spremnik za odvojivu prednju ploèu
\CQ-RX200N\ \CQ-RX103N\ \CQ-RX102N\ \CQ-RX101N\
Zahtjev za uporabom spremnika za prednju ploèu:
Sprijeèite probleme i osigurajte prednju ploèu, upotrebljavajte dodatni
spremnik za odvojivu prednju ploèu (YGFA134302).
Uputstva za uporabu
(hrvatski: YGFM286051)
1 set
\CQ-RX400N\ \CQ-RX300N\
Vodiè za nadogradnju
Upute za montažu
: YGFM294417)
(Jamstveni list)
Set za montažu (YEP0FZ5700)
Klinovi za demonažu
1 set
Vijak za montažu (5 mm )
Brojevi u zagradama ispod svakog pojedinaènog pribora, su
brojevi koji služe za održavanje i servis.
Pribor i njegovi pridruženi brojevi su podložni promjeni bez
prethodne najave.
Montažni okvir i prednji okvir su tvornièki postavljeni na ureðaj.

hrvatskity Information

Q Read the operating instructions for the unit and all other
components of your car audio system carefully before using the
system. They contain instructions about how to use the system in
a safe and effective manner. Panasonic assumes no responsibility
for any problems resulting from failure to observe the instructions
given in this manual.
This pictograph intends to alert you to the presence
of important operating instructions and installation
instructions. Failure to heed the instructions may result
in severe injury or death.
Q This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs
are explained below. It is important that you fully understand the
meanings of the pictographs in order to use this manual and the
system properly.
This pictograph intends to alert you to the presence
of important operating instructions and installation
instructions. Failure to heed the instructions may result in
injury or material damage.
Observe the following warnings when using this unit.R The driver should neither watch the display nor operate the system while driving.
Watching the display or operating the system will distract the
driver from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
R Use the proper power supply.
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other
battery systems, especially a 24 V DC battery system.
R Keep batteries and insulation fi lm out of reach of infants.
Batteries and insulation fi lm can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation fi lm,
please seek immediate medical attention.
R Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
R Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the
product yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Centre.
R Do not use the unit when it is out of order.
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
R The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the fl oor while
driving, get wedged under the brake pedal, and lead to a traffi c
R Refer fuse replacement to qualifi ed service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualifi ed service
engineer. Incorrect replacement of the fuse may lead to smoke,
re, and damage to the product.
Observe the following warnings when installing.R Disconnect the lead from the negative (–) battery terminal before installation.
Wiring and installation with the negative (–) battery terminal
connected may cause electrical shock and injury due to a short
circuit. Some cars equipped with the electrical safety system have
specifi c procedures of battery terminal disconnection.
R Never use safety-related components for installation, grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or
xing the product or its accessories.
R Installing the product on the air bag cover or in a location where it interferes with airbag operation is prohibited.R Check for piping, gasoline tank, electric wiring, and other items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, fi rst check where the wire harness, gasoline tank,
and electric wiring are located. Then open the hole from outside if
R Never install the product in a location where it interferes with your fi eld of vision.R Never have the power cord branched to supply other equipment with power.R After installation and wiring, you should check the normal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
re, electrical shock or a traffi c accident.
R In the case of installation to an airbag-equipping car, confi rm warnings and cautions of the vehicle manufacturer before installation.R Make sure the leads do not interfere with driving or getting in and out of the vehicle.R Insulate all exposed wires to prevent short circuiting.
Observe the following cautions when using this unit.R Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffi c
conditions while driving.
R This unit is designed for use exclusively in automobiles.R Do not operate the unit for a prolonged period with the engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
R Do not expose the unit to direct sunlight or excessive heat.
Otherwise these will raise the interior temperature of the unit, and
it may lead to smoke, fi re, or other damage to the unit.
R Do not use the product where it is exposed to water, moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fi re, or other damage to the unit. Make especially sure that
the unit does not get wet in car washes or on rainy days.
R Set the volume level to low enough before the AUX connection is completed.
Failure to observe this, the loud noise may come out and damage
your speakers and your hearing. Direct connection of the speaker/
headphone output of an external device without any attenuator
may distort sound or damage the connected external device.
Observe the following cautions when installing.R Refer wiring and installation to qualifi ed service personnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is not
liable for any problems resulting from your own installation of the
R Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fi re.
R Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect the
leads by winding them with vinyl tape or similar protection.
R Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied
or designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fi re.
R Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to overheat
and will result in fi re or other damage.
R Do not install the product where it is exposed to strong vibrations or is unstable.
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
R Installation Angle
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed. Consult
your dealer for further details.
R Wear gloves for safety. Make sure that wiring is completed before installation.R To prevent damage to the unit, do not connect the power connector until the whole wiring is completed.R Do not connect more than one speaker to one set of speaker leads. (except for connecting to a tweeter) Observe the following cautions when handling the battery for the remote control unit.
\CQ-RX400N\ \CQ-RX300N\
• Use only specifi ed battery (CR2025).
• Match the polarity of the battery with the (+) and (–) marks in the
battery case.
• Replace a dead battery as soon as possible.
• Remove the battery from the remote control unit when not using it
for an extended period of time.
• Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
• Dispose of the battery according to the local regulations.
• Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fi re or water.
In case of battery leakage
• Thoroughly wipe the battery liquid off the battery case and insert
new battery.
• If any part of your body or clothing comes into contact with battery
liquid, wash it with plenty of water.
• If battery liquid comes into contact with your eyes, wash them with
plenty of water and get immediate medical attention.
Observe the following cautions when using USB device.
\CQ-RX400N\ \CQ-RX300N\
• Do not connect a USB device directly to this unit. If the USB device
is connected directly to this unit and an accident occurs, or if the
brakes are applied suddenly, the driver or passenger may bump
into the USB device and may get injured.
• Position the USB device and USB extension cable so that they do
not obstruct your driving.
• Do not connect any USB device other than USB memory, a USB
audio player or iPod series (\CQ-RX400N\). Do not connect multiple
USB devices to the USB connector. Drawing power for multiple
USB devices from the connector could cause overheating and
Caution LabelDeck Ass’y (in the unit, upper side)
Laser Product
Label Indications and Their Locations
CAUTIONLASER RADIATION WHEN OPEN. DO NOT STARE INTO BEAM.CLASS 1 LASER PRODUCTInformation on Disposal for Users of Waste Electrical & Electronic Equipment (private households)
This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be
mixed with general household waste.
For proper treatment, recovery and recycling, please take these products to designated collection points, where they will be
accepted on a free of charge basis. Alternatively, in some countries you may be able to return your products to your local retailer
upon the purchase of an equivalent new product.
Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on human
health and the environment which could otherwise arise from inappropriate waste handling. Please contact your local authority
for further details of your nearest designated collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.
For business users in the European Union
If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.
Information on Disposal in other Countries outside the European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.
This product utilizes a laser.Use of controls or adjustments or performance of procedures other than those specifi ed herein may result in hazardous radiation exposure.Do not take apart this unit or attempt to make any changes yourself.
This unit is a very intricate device that uses a laser
pickup to retrieve information from the surface of
compact discs. The laser is carefully shielded so that its
rays remain inside the cabinet.
Therefore, never try to disassemble the player or alter
any of its parts since you may be exposed to laser rays
and dangerous voltages.
(Bottom of the unit)

Before Reading These Instructions

Panasonic welcomes you to our constantly growing family of electronic products owners.
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
\CQ-RX400N\ \CQ-RX300N\ \CQ-RX200N\
The instruction manual consists of 2 books. One is “Operating Instructions” describing the operations of the main unit.
The other is “System Upgrade Guidebook” describing the optional devices such as CD changer.
Differences Among 6 Models
This operating instruction manual is for 6 models CQ-RX400N, CQ-RX300N, CQ-RX200N, CQ-RX103N, CQ-RX102N and CQ-RX101N. All illustrations throughout
this manual represent model CQ-RX400N unless otherwise specifi ed. The following table describes the differences among 6 models.
ModelsFeaturesCQ-RX400N CQ-RX300N CQ-RX200N CQ-RX103N CQ-RX102N CQ-RX101NRemovable Face Plate CaseIncluded Included Not included Not included Not included Not includedRemote Control UnitIncluded Included Not included Not included Not included Not includedSystem Upgrade GuidebookIncluded Included Included Not included Not included Not includedSystem-up ConnectorSupported Supported Supported Not Supported Not Supported Not SupportedPreamp Out Connector2 (Front/Rear) 2 (Front/Rear) 1 (Rear) 1 (Rear) 1 (Rear) 1 (Rear)USB ConnectorSupported (USB iPod)Supported Not Supported Not Supported Not Supported Not SupportedAAC playbackSupported Supported Not Supported Not Supported Not Supported Not Supported
Button logo colour Blue Red Red Blue Green Red


Your product is designed and manufactured to ensure the minimum of maintenance. Use a dry, soft cloth for routine exterior
cleaning. Never use benzine, thinner, or other solvents.
If the fuse blows out, consult your dealer, or your nearest authorized Panasonic Service Centre.

Anti-Theft System

This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
the Unit
Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
If dirt or other foreign substances get on the contacts, wipe
them off with a clean and dry cloth.
Face Plate Removing/Mounting
(Anti-Theft System)
• Use fuses of the same specifi ed rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit directly
without a fuse could cause fi re or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Service Centre.
Turn off the power.
Press []. The face plate will open.
Pull it out toward you.
\CQ-RX400N\ \CQ-RX300N\
Put the face plate in the case.
Slide the left side of the face plate in place.
Press the right end of face plate until a “click” is heard.
Expansion Module (Hub Unit)
\CQ-RX400N\ \CQ-RX300N\ \CQ-RX200N\
Connection of the Expansion Module (hub unit, CY-EM100N) allows
users to connect up to 4 optional devices shown below.
Wide Array of Components for System Upgrade
\CQ-RX400N\ \CQ-RX300N\ \CQ-RX200N\
Various optional components allow users to obtain availability of wide range of
system upgrade. Upgrading the system delivers relaxed AV space in a car. For
further information, refer to the separate System Upgrade Guidebook.
The optional adaptor (Direct Cable for iPod: CA-DC300N) allows you to connect the optional iPod series. iPod is a trademark of Apple Inc., registered in the U.S. and other countries.• CD ChangerThe optional adaptor (Conversion Cable for DVD/CD Changer: CA-CC30N) allows you to connect the optional Panasonic CD changer unit (CX-DP880N).
Using the optional Bluetooth Unit (CY-BT200N) and a Bluetooth
device enables hands-free telephony and Bluetooth Audio listening
with this unit.
Note: This unit does not support CY-BT100N.
The Bluetooth word mark and logo are owned by the Bluetooth SIG,
Inc. and any use of such marks by Matsushita Electric Industrial Co.,
Ltd. is under license. Other trademarks and trade name are those of
their respective owners.


SQ (Sound Quality)
You have 6 preset modes (FLAT, ROCK, POP, VOCAL, JAZZ, CLUB). You
can customize your settings for these and save them for instant recall.
SQ3 (3-Band Sound Quality)
Center frequency and level are adjustable in each of 3 bands. This lets
you fi ne-tune sound quality for each genre to suit car-interior acoustics
and your personal preferences. (
« “Sound Control”)
USB Connector
\CQ-RX400N\ \CQ-RX300N\
The USB Connector is equipped on the front panel. (« System
Upgrade Guidebook)
By connecting a USB memory (not included) to USB connector via a
USB extension cable (USB 2.0, not included), you can enjoy MP3/
WMA/AAC fi les stored on the USB memory (not included) in your car.
By connecting iPod series to USB connector via a USB extension cable
for iPod (USB 2.0, not included), you can enjoy music fi les stored on
the iPod series in your car.
AUX (AUX1) Input Terminal
The AUX input terminal is equipped on the front panel.
Your mobile audio player and other devices are connectable to this unit
without any diffi culty.
Printed in China

Specifi cations

Power supply : DC 12 V (11 V – 16 V DC), test
voltage 14.4 V, negative ground
Current consumption : Less than 2.1 A
(CD mode; 0.5 W x 4 channels)
Maximum power output : 50 W x 4 channels (at 1 kHz),
volume control maximum
Power output : 22 W x 4 channels
(DIN 45 324, at 4 j )
Tone/SQ adjustment range : SQ Low/Bass: ±12 dB
(at 60 Hz, 80 Hz, 100 Hz, 200 Hz)
SQ Mid: ±12 dB
(at 500 Hz, 1 kHz, 2 kHz, 3 kHz)
SQ High/Treble: ±12 dB
(at 10 kHz, 12 kHz, 15 kHz, 18 kHz)
Speaker impedance : 4 – 8 j
Pre-amp output voltage : 2.0 V (CD mode, 1 kHz, 0 dB)
Pre-amp output impedance : 200 j
USB Connector \CQ-RX400N\ \CQ-RX300N\
USB Standard Compatibility
: 1.1/2.0 Full Speed
Maximum Supply Current : 500 mA
Front AUX input
Input impedance : 10 kj
Allowable external input : 2.0 V
Connector : 3.5 mm Stereo mini-pin
Dimensions (W x H x D) : 178 x 50 x 160 mm
Weight : 1.2 kg
Disc Player
Sampling frequency : 8 times oversampling
DA converter : 1 bit DAC System
Pick-up type : Astigma 3-beam
Light source : Semiconductor laser
Wave length : 790 nm
Frequency response : 20 Hz – 20 kHz (±1 dB)
Signal to noise ratio : 96 dB
Total harmonic distortion : 0.01 % (1 kHz)
Wow and fl utter : Below measurable limits
Channel separation : 85 dB
Sales and Support Information
For UK and Ireland customers only.Direct Sales at Panasonic UK
Order accessories and consumable items for your product with ease and
confi dence by phoning our Customer Care Centre Monday - Thursday
9:00am - 5:30pm, Friday 9:30am - 5:30pm. (Excluding public holidays).
Or go on line through our Internet Accessory ordering application at
Most major credit and debit cards accepted.
All enquiries, transactions and distribution facilities are provided
directly by Panasonic UK Ltd.
It couldn’t be simpler!
Also available through our Internet is direct shopping for a wide range of
nished products, so take a browse on our website for further details.
Customer Care Centre
For customers within the UK: 0844 844 3852
For customers within the Republic of Ireland: 01 289 8333
Visit our website for product information
• E-mail:
Remote Control Unit for CQ-RX200N/CQ-RX103N/CQ-RX102N/
CQ-RX101N is option (CA-RC80N).
The optional remote control is available from your local dealer.
Track selection
Fast forward/fast reverse
FM Radio
Frequency range : 87.5 MHz – 108.0 MHz
Usable sensitivity : 6 dB/μV (S/N 30 dB)
Stereo separation : 35 dB (at 1 kHz)
AM (MW) Radio
Frequency range : 531 kHz – 1 602 kHz
Usable sensitivity : 28 dB/μV (S/N 20 dB)
AM (LW) Radio
Frequency range : 153 kHz – 279 kHz
Usable sensitivity : 32 dB/μV (S/N 20 dB)
• Specifi cations and design are subject to modifi cation without
notice due to improvements.
Some fi gures and illustrations in this manual may be different
from your product.
Authorized Representative
[Requirements of the EMC directive]:
Panasonic Testing Centre
Panasonic Marketing Europe GmbH
Winsbergring 15, 22525 Hamburg, F.R. Germany
Matsushita Electric Industrial Co., Ltd.
Web Site:

Notes on MP3/WMA/AAC

Notes on MP3/WMA/AAC
Playable Audio File
Notes for AAC playback is only for the model CQ-RX400N/
What is MP3/WMA/AAC?
MP3* (MPEG Audio Layer-3) and WMA (Windows Media
Audio) are the compression formats of digital audio.
The former
is developed by MPEG (Motion Picture Experts Group), and
the latter is developed by Microsoft Corporation. Using these
compression formats, you can record the contents of about
10 music CDs on a single CD media (This fi gures refer to data
recorded on a 650 MB CD-R or CD-RW at a fi xed bit rate of
128 kbps and a sampling frequency of 44.1 kHz).
*MPEG Layer-3 audio coding technology licensed from
AAC is an abbreviation for “Advanced Audio Coding”.
It has been defi ned as a standard for audio compression
technology using MPEG 2 and MPEG 4.
Note: MP3/WMA/AAC encoding and writing software is not
supplied with this unit.
Points to Remember When Making MP3/
High bit rate and high sampling frequency are recommended
for high quality sounds.
Selecting VBR (Variable Bit Rate) is not recommended
because playing time is not displayed properly and sound
may be skipped.
The playback sound quality differs depending on the
encoding circumstances. For details, refer to the instructions
of your own encoding software and writing software.
It is recommended to set the bit rate to “128 kbps or more”
and “fi xed”.
It is recommended to set the bit rate to “64 kbps or more”
and “fi xed”.
Do not set the copy protect attribute on the WMA fi le to
enable this unit to play back.
It is recommended to set the bit rate to “128 kbps or more”
and “fi xed”.
The formats and extensions for AAC data vary according to
the encoder software used.
AAC fi les which can be played on this unit have the “.m4a”
extension and were encoded with Apple iTunes
version 7.
The fi le extension for fi les encoded with the iTunes Apple
Lossless Encoder is “.m4a”, but such fi les cannot be played
on this player.
Files under copyright protection cannot be played.
Never assign the “.mp3”, “.wma” or “.m4a” le
name extension to a fi le that is not in the MP3/
WMA/AAC format. This may not only produce
noise from the speaker damage, but also damage
your hearing.
iTunes is a trademark of Apple Inc., registered in the U.S.
and other countries/regions.
Windows Media, and the
Windows logo are trademarks, or
registered trademarks of Microsoft
Corporation in the United States
and/or other countries/regions.
Notes on MP3/WMA/AAC (continued)
Display Information
Displayed items
Disc title
Track title
MP3 (ID3 tag)
Album name
Title name/artist name
Folder name
File name
WMA (WMA tag)
Album name
Title name/artist name
AAC (Song information)
Album name
Title name/artist name
Displayable characters
Displayable length of fi le name/folder name: within
32 characters. (Unicoded fi le and folder names are reduced
by half in the number of displayable characters.)
Name fi les and folders in accordance with the standard of
each fi le system. Refer to the instructions of writing software
for details.
ASCII character set and special characters in each language
can be displayed.
Some Cyrillic characters in the Unicode can be displayed.
ASCII character set
A to Z, a to z, digits 0 to 9, and the following symbols:
(space) ! ” # $ % & ’ ( ) * + , - . / : ; < = > ? @ [ \ ] ˆ _ ` { | } ~
Special Characters
À Á Â Ã Å à á â ã å
Ä ä
Ò Ó Ô Õ Ö ò ó ô õ ö
Ù Ú Û Ü ù ú û ü
With some software in which MP3/WMA/AAC format fi les
have been encoded, the character information may not be
displayed properly.
Undisplayable characters and symbols will be converted into
an asterisk (
It is recommended that the length of the fi le name is less
than 8 characters (excluding the fi le extension).
Recording MP3/WMA/AAC Files on a CD-
You are recommended to minimize the chances of making
a disc that contains both CD-DA fi les and MP3/WMA/AAC
If CD-DA fi les are on the same disc as MP3, WMA or AAC
les or the songs may not play in the intended order, or
some songs may not play at all.
When storing MP3 data, WMA data or AAC data on the
same disc, use different folders for each data.
Do not record fi les other than MP3/WMA/AAC fi les and
unnecessary folder on a disc.
The name of an MP3/WMA/AAC fi le should be added by
rules as shown in the following descriptions and also comply
with the rules of each fi le system.
The fi le extension “.mp3”, “.wma” or “.m4a” should be
assigned to each fi le depending on the fi le format.
You may encounter trouble in playing MP3/WMA/AAC fi les or
displaying the information of MP3/WMA/AAC fi les recorded
with certain writing software or CD recorders.
This unit does not have a play list function.
Although Multi-session recording is supported, the use of
Disc-at-Once is recommended.
Supported fi le systemsQCD-media
ISO 9660 Level 1/Level 2, Apple Extension to ISO 9660, Joliet,
Note: Apple HFS, UDF 1.50, Mix CD and CD Extra are not
QUSB-device \CQ-RX400N\ \CQ-RX300N\
File system is FAT12/16/32
Compression formats
(Recommendation: “Points to Remember When Making MP3/WMA/AAC Files” «Left)
\CQ-RX400N\ \CQ-RX300N\
Compression method Bit rate VBR Sampling frequency
MPEG 1 Audio Layer-3 (MP3) 32 k – 320 kbps Yes 32, 44.1, 48 kHz
MPEG 2 Audio Layer-3 (MP3) 8 k – 160 kbps Yes 16, 22.05, 24 kHz
MPEG 2.5 Audio Layer-3 (MP3) 8 k – 160 kbps Yes 8, 11.025, 12 kHz
Windows Media Audio Ver. 2B9*64 k – 160 kbps Yes 32, 44.1, 48 kHzMPEG 4 Advanced Audio Coding Low Complexity (AAC LC)16 k – 320 kbps Yes 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz* WMA 9 Professional/LossLess/Voice are not supported.
Notes on MP3/WMA/AAC (continued)
Folder Selection Order/File Playback Order
Maximum number of fi les/folders
Maximum depth of trees: 8
\CQ-RX400N\ \CQ-RX300N\
Maximum number of fi les
CD-media: 999
USB device: 65 535
Maximum number of fi les in one folder
CD-media: 999
USB device: 999
Maximum number of folders:
CD-media: 256 (Root folder is included.)
USB device: 255 (Root folder is included.)
\CQ-RX200N\ \CQ-RX103N\ \CQ-RX102N\ \CQ-RX101N\
Maximum number of fi les: 999
Maximum number of fi les in one folder: 999
Maximum number of folders: 256 (Root folder is included.)
You can shorten the duration between data read and
playback by decreasing the quantity of fi les or folders, or the
depth of the hierarchy.
This unit counts the number of folders irrespective of the
presence or absence of an MP3/WMA/AAC fi le.
If the selected folder does not contain any MP3/WMA/AAC
les, the nearest MP3/WMA/AAC fi les in the order of
playback will be played.
Playback order may be different from other MP3/WMA/AAC
players even if the same disc is used.
“ROOT” appears when displaying the root folder name.
\CQ-RX400N\ \CQ-RX300N\
Empty folders stored on the USB memory are not included in
the folder count.
Depending on the connected USB memory, the order in
which the fi les are played back may differ to the order in
which the fi les were stored.
Root folder
(Root Directory)
Folder Selection
In the order
Tree 1 Tree 2 Tree 3
Tree 4 Tree 8 (Max.)
File Selection
In the order
\CQ-RX400N\ \CQ-RX300N\
Tree 1 Tree 2 Tree 3
Tree 4 Tree 5 Tree 8 (Max.)
Root folder
(Root Directory)
Folder Selection
In the order
File Selection
In the order
\CQ-RX200N\ \CQ-RX103N\ \CQ-RX102N\ \CQ-RX101N\
Compression method Bit rate VBR Sampling frequency
MPEG 1 Audio Layer-3 (MP3) 32 k – 320 kbps Yes 32, 44.1, 48 kHz
MPEG 2 Audio Layer-3 (MP3) 8 k – 160 kbps Yes 16, 22.05, 24 kHz
MPEG 2.5 Audio Layer-3 (MP3) 8 k – 160 kbps Yes 8, 11.025, 12 kHz
Windows Media Audio Ver. 2B9*64 k – 160 kbps Yes 32, 44.1, 48 kHz* WMA 9 Professional/LossLess/Voice are not supported. If You Suspect Something Wrong
Check and take steps as described below.
If the described suggestions do not solve the problem, it is
recommended to take the unit to your nearest authorized Panasonic
Service Centre. The product should be serviced only by qualifi ed
personnel. Please refer the checking and the repair to professionals.
Panasonic shall not be liable for any accidents arising out of neglect
of checking the unit or your own repair after your checking.
Never take measures especially those other than
indicated by italic letters in “Possible Solution” described
below because those are too dangerous for users to
handle themselves.


• Do not use the unit in an irregular condition, for example,
without sound, or with smoke or a foul smell, which can cause
ignition or electric shock. Immediately stop using the unit and
consult your dealer.
• Never try to repair the unit by yourself because it is dangerous
to do so.
No power Start the engine. (Or turn the ignition
switch to the ACC position.)
Verify the wiring. (battery lead, power
lead, ground lead, etc.)
Fuse blown (Contact the nearest Panasonic
Service Centre.)
Ask a professional for fuse replacement. Be sure to use the same rated fuse.No sound Disable the mute function. Verify the wiring. Wait until the dew disappears before
turning on the unit.
Noise Make sure that grounding is established
No sound from left, right, front, or rear speaker Adjust the balance and fader. Verify the wiring.Left and right sounds are reversed Connect the speaker lead correctly.
Frequent noise Tune in to another station of high-intensity
Make sure that the antenna mounted point
is grounded properly.
Preset data deleted The preset memory is cleared to return
to the original factory setting when
the power connector or battery is
Error Display Messages (Disc Player)
(The disc is ejected automatically.)
The disc is dirty or upside down.
Check the disc.
(The disc is ejected automatically.)
The disc has scratches.
Check the disc.
No operation by some cause.
If normal operation is not restored,
consult your dealer or the nearest
Service Centre to ask for repairs.
Cannot read the fi le
Check the disc.
A WMA/AAC fi le can be copyrighted.
The fi le protected by copyright is not
Trouble Possible Solution Trouble Possible Solution
\CQ-RX400N\ \CQ-RX300N\ \CQ-RX200N\
Note: Refer to the System Upgrade Guidebook for error messages
regarding optional products.
Disc Player
No sound, or disc is automatically ejected Load the disc correctly. Clean the disc.Sound skip, poor sound quality Clean the disc.Sound skip due to vibration The maximum permissible tilt angle is
Secure the unit.Disc not ejectable
Press []. If the disc is still not ejected,
contact the nearest Panasonic Service

Notes on Discs

otes on CD/CD Media (CD-ROM, CD-R, CD-RW)
Printed side
How to hold the disc
Do not touch the underside of the disc.
Do not scratch on the disc.
Do not bend the disc.
When not in use, keep disc in the case.
Do not use discs that fi t any of the descriptions given
below. Using these discs may damage the discs or cause
the unit to malfunction.
Special discs in a shape which is not round
Partly or wholly transparent disc
Wholly transparent disc Partly transparent disc
Wholly semi-transparent disc may not be played back.
Discs with adhered labels, etc. on them
Disc with adhered stickers
or tape
Labels created by a printer
Protective fi lms or sheets Discs accessories (stabilizers,
Damaged or deformed discs
Shoddily made discs Discs with cracks, scratches or
parts missing
Discs with burrs
Please remove the burrs
before use.
Disc Insert
The surfaces of new discs tend to be slippery. Therefore,
when using such a disc for the fi rst time, it may not load
satisfactorily even when it has been inserted into the unit. At
a time like this, insert the disc into the unit as far as it will go
until it is loaded properly.
• When inserting a disc into or ejecting and removing it
from the unit, insert it straight in or eject and remove it
straight out in parallel with the unit.
Observe, the disc may be scratched or marked in the
• When inserting a disc, do not put one disc on another.
Failure to observe this may cause the discs to be
Do not leave discs in the following places:
• Direct sunlight
• Near car heaters
Dirty, dusty and damp areas
On seats and dashboards
Disc cleaning
Use a dry, soft cloth to wipe from the center outward.
<Correct> <Wrong>
Do not attach any seals or labels to your discs.
Do not write on the disc label in a heavy pen or ballpoint
Notes on CD-Rs/RWs
You may have trouble playing back some CD-R/RW discs
recorded using CD recorders (CD-R/RW drives), either
due to their recording characteristics or dirt, fi ngerprints,
scratches, etc. on the disc surface.
CD-R/RW discs are less resistant to high temperatures
and high humidity than ordinary music CD. Leaving them
inside a car for extended periods may damage and make
playback impossible.
The unit may not successfully playback a CD-R/RW,
that was made by the combination of writing software,
a CD recorder (CD-R/RW drive) and a disc if they are
incompatible with one another.
This player cannot play the CD-R/RW discs if the session is
not closed.
Be sure to observe the handling instructions of CD-R/RW
This player cannot play CD-R/RW discs which contain
other than CD-DA or MP3/WMA/AAC data (Video CD, etc.).
If you use commercial CDs, they must have either of these labels shown at
Some copy-protected music CDs are not playable.
It is prohibited by copyright laws to copy, distribute and
deliver copyrighted materials such as music without the
approval of copyright holder except enjoying yourself
No warranty
Above description complies with our investigations as of
September 2007. It has no warranty for reproducibility and
displayability of MP3/WMA/AAC.
YGFM286051A FT1007-1117
N_01EN.indd 1N_01EN.indd 1 2007/10/25 13:38:002007/10/25 13:38:00

User manual

View the manual for the Panasonic CQ-RX102N here, for free. This manual comes under the category Car Radios and has been rated by 2 people with an average of a 7.2. This manual is available in the following languages: English. Do you have a question about the Panasonic CQ-RX102N or do you need help? Ask your question here

Need help?

Do you have a question about the Panasonic CQ-RX102N and the answer is not in the manual? Ask your question here. Provide a clear and comprehensive description of the problem and your question. The better your problem and question is described, the easier it is for other Panasonic CQ-RX102N owners to provide you with a good answer.

Number of questions: 0

Panasonic CQ-RX102N specifications

Below you will find the product specifications and the manual specifications of the Panasonic CQ-RX102N.

Brand Panasonic
Model CQ-RX102N
Product Car Radio
Language English
Filetype manual_type_manual (PDF)

Questions & answers

Can't find the answer to your question in the manual? You may find the answer to your question in the FAQs about the Panasonic CQ-RX102N below.

Is your question not listed? Ask your question here

No results